Features:
Size 1/2" to 4" BSP & Solvent Weld
Body UV stabalised PVC
Seat PTFE
Pressure 10 BAR
Temperature Ambient
Actuation Double Acting Pneumatic
2 way UV stabilised PVC ball valve with double acting pneumatic actuator. Comes with PTFE (Teflon) seats and our unique double stem seal system (standard in EPDM but also available in Viton). Great for corrosive or chemical media where traditional material such as brass and stainless steel are not suitable. Anodised aluminium actuator with visual indicator. Commonly used in the aquaculture industry (sea water), chemical dosing, water treatment and pool filtration. Available in BSP threaded (Threads conform to ISO 7.1 Sealing Threads.) and solvent weld ends (ANSI Standard designed to fit Schdule 40 & 80 pipe).
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
| 0°C to 60°C |
Size 1/2" to 4" BSP & Solvent Weld
Body UV stabalised PVC
Seat PTFE
Pressure 10 BAR
Temperature Ambient
Actuation Double Acting Pneumatic
-
What is a 2 Way Double Acting Pneumatic PVC Ball Valve?
A two way double acting UPCV ball valve is constructed of UV Stabalised PVC. It has a mounted anodised aluminium double acting (air open, air close) rack and pinion actuator fixed to the valve by an aluminium bracket which conducts its 90 degree turn (open,close). They have a teflon (PTFE) seat with either EPDM or FKM seals. The ends can either be threaded or solvent weld and are interchangable by unscrewing the end connector. The actuator has a namur interface and position indicator.
-
How does a Two Way Double Acting UPVC Ball Valve work?
The 2 way double acting UV Stabalised PVC ball valves works the same as any normal two way ball valve, whereby the ball is rotated 90 degrees within the body of the valve which will either open or close the valve. The ball itself has a hole at either end which the media will flow through when it is open. When the valve is closed, these holes are blocked off to the flow effectively isolating the media either side of the valve. The ball is turned by a double acting rack & pinion actuator which is connected to a shaft which in turn is mated to the ball by a female slot. When the actuator is operated by a 5/2 valve (all double acting actuators need a 5/2 valve to operate, the most common we see is a 5/2 direct interfacing namur solenoid valve) the shaft will be rotated effectively turning the ball inside the cavity and switching it to its other state (either open or close). Extras such as limit switch boxes and positioners can also be mounted directly to the actuator.
-
How long will my UV Stabalised Double Acting PVC Ball Valve last?
Like any valve this depends upon the usage case of your ball valve, its environment, media and how many times it is cycled. For instance if it is on a clean media, in a clean environment and not cycled regularly the life will be decades or more. If it is on a corrosive media and in a dry application with a high cycle rate the life will be much shorter. Repair kits are readily available for valve refurbishment if the application requires. The actuators life will depend upon how clean and dry the supply air is (the air that makes the actuator operate) however we regularly test these to over 800,000 cycles. Install a basic air filter if you are not sure about the quality of your air, we have pneumatic actuators that have been in operation for decades. The most common failure we see is due to dirty wet air being sent to the actuator.
-
How do I install a Double Acting PVC Ball Valve?
As this is a 2 way valve it will need to be fitted between either two threaded or two solvent weld connections (the valve has two female ends). The double acting actuator can accommodate a namur solenoid valve which is a very popular configuration (the 5/2 control valve bolts directly onto the actuator with an o-ring face seal on the back of the valve) or just a standalone 5/2 valve. If you are using a stand alone 5/2 valve, the air lines will need to be run from here into the ports on the actuator (remember the longer the run the slower the operation unless you use quick exhaust valves near the actuator).
-
What are typical uses of a two way Double Acting Pneumatic PVC ball valve?
These double acting PVC ball valves are mainly used in water treatment or corrosive media and environment such as salt water. Being double acting pneumatic they are not used in fail safe applications as if you lose air it will just stay in its current configuration (if you need fail safe choose a spring return option for the actuation).
-
How long will my product take to get to me?
This depends upon where you are based and the freight method chosen. If the express freight option is selected it is usually next day delivery to metropolitan areas in Australia for under 5kg. If free freight has been selected it will go by road freight which can be anywhere from 1 to 10 days depending upon your location. It usually averages 3 days.
-
What warranty do I get?
All of our products come standard with a 12 month warranty. The good news is we have very strict quality controls and all valves leave our warehouse tested (full material and testing certificates to API598 are available) and inspected so there are rarely any issues. Also once your valve is in and operating it will most likely continue to do so for a very long time.
